发射器与接收机配对
1、发射器配发射器
▲Paring of transmitters
注:以下两个发射器分别引用“A发射器”和“B发射器”
Note: The following two transmitters are represented as“Transmitter A”,and“Transmitter B”rrespectively
1.“A发射器”装入电池,按下急停开关,让急停处于断开状态;
▲ Install a battery into“Transmitter A”,press the emergency stop switch and keep it power -off;
2.按下“启动按键”(按着不松开);
▲Press the“START”(hold down);
3.连续按“上键”5次,直到运行指示灯(绿灯)闪烁。此时发射处于主动发射配对模式;
▲Press“UP” for consecutive 5 times till the operation ind icators(green light)flicker The transmitter is in active tran smission pairing mode at the moment;
4.“B发射器”装入电池,按下急停开关,让急停处于断开状态;
▲ Inslall a ballery in “Transrmiller B",press he errergency stop switch and keep it powerofft;
5.按下“启动按键”(按着不松开);
▲Press the“START”(hold down);
6.连续按“下键”5次,直到运行指示灯(红灯)常亮。此时发射处
于主动接收配对模式:
▲Press“DOWN”for consecutive 5 times till the operation indicators(red light) always bright The transmitter is in ac tive receiving pairing mode at the moment;
7.等两个发射器指示灯都熄灭。(此时配对成功)
▲Wait unitl both transmitter lights go off.(pairing is successful)
▲发射器配接收机
▲Pairing of transmitter and receiver
1.“发射器”装入电池,按下急停开关,让急停处于
▲ Install a battery in 'transmitter” press the emergency stop switch and keep it
断开状态;按下“启动按键”(按着不松开);
▲power-off;Press the“START”(hold down);
2.连续按“下键”5次,直到运行指示灯(红灯)常亮。此时发射处
于主动接收配对模式;
▲Press“DOWN”for consecutive 5 times till the operation indicators(red light) always bright The transmitter is in ac tive receiving pairing mode at the moment;
3.开启接收机电源,接收机会自动发射5秒的配对信号;
▲After powering on,the receiver will transmit pairing signals for 5s automatically;
4.等发射器信号灯熄灭。(此时配对成功)
▲Wait for transmitter light to go off (pairing successful).
操作步骤
注:请遵照以下操作步骤
Note: Please observe the following operation steps
1.请确认发射器内部电池饱满,接收机以上电;
▲Confirm the transmitter battery is full and the receiver is powered on;
2.顺时针旋转红色急停开关;
▲ Clockwise rotate the red emergency stop switch;
3.按“START”启动键开机;
▲Press“START” to power on;
4.按照相关方向操作遥控动作;
▲Operate the remote control by pressing direction keys;
5.操作结束后,应按停止键停止接收机。
▲After operation,press“STOP” to stop the receiver
6.将红色急停开关压下置于(OFF)状态,关闭接收机电源。
▲Shift the red emergency stop switchto“OFF”to power off the receiver.
注:当发生紧急情况时,请执行第“5”和第“6”操作,需要时通知经销商或拨打本公司的技术支持电话,寻求帮助。
Note: In emergency case, please operate according to“5 and“6”; if necessary, report to the dealer or call our technical support number for solution.
1、当遥控器不能动作时,请按照以下步骤检查故障
▲When remote control fails to act please check in following steps:
2、请确认发射器和接收机的地址码和无线频道是否一致;
▲Please confirm whether the address code and wireless channel of transmitter and receiver are consistent;
3、请确认接收机电源是否正常
▲Please contirm whether the power supply of receiver is normal or not;
4、按着启动键,观察指示灯是否正常的绿色闪烁,如果红灯常亮,表示电池欠压,应更换电池;
▲Hold down“START"and observe whether the green indicator of transmitter flashes; if the red light is normally-on,it indicates the battery is under-voltage, please
change it;
5、如果一切正常遥控仍没有动作,请与经销商联系,或拨打公司技术电话。
▲AIf there is no fault but the remote control fails to act, please contact with the dealer or call our technical support number.
1、未经专业培训,不得拆开本机器,否则后果自负;
▲Do not disassemble the machine without professional training,or suffer the consequences;
2、发射器和接收机的地址码和无线频道必须一致才能使用;
▲The transmitter and receiver can be used together only when the address code and wireless channel are consistent;
3、接收机安装位置必须远离变频器、电动机及其链接电缆至少3米以上距离,以避免接收机收到无关信号的干扰;
▲To avoid interference from irrelevant signals the receiver shall be installed at least 3m away from frequency converter, motor and connecting cables;
4、接收机不可安装在电控箱内,正确的安装方式是将接收机固定在电控箱外部的适当位置,然后再将接收机输出电缆穿入控电箱内做适当的接线;
▲The receiver shall not be installed inside the electric control cabinet, but fixed in a suitable position outside, and the out-put cable shall be penetrated into cabinet as a flexible wire;
5、200米范围内不可使用相同无线频道的设备,以避免无线信号相互干扰;
▲To avoid radio interference equipment in same wireless channel shall not be used within 200m;
6、使用设备应具备电源总停接触器、限位开关等安全设施;
▲The equipment shall be equipped with safety facilities such as master stop contactor and limit switch.
7、使用完毕后应先将遥控器的总停按键按下,然后将急停开关按下。后应关闭行车总电源,以切断接收机电源。
▲After using, press the master stop button of remote controller,then press the emergency stop switch.F inally, turn off the main power of crane and power off the receiver.